Set of 2 profiled counter-irons Height 48 x 5.3 mm Special A215 shelf moulding for router tool holders - Diamwood Platinum
Ref. DW-PLA477479CFHT50009
En savoir + sur Set of 2 profiled counter-irons Height 48 x 5.3 mm Special A215 shelf moulding for router tool holders - Diamwood Platinum
Set of 2 profiled counter-irons Ht. 48 x 5.3 mm special shelf moulding A215 for router toolholders. The counter-irons must be used with profiled irons mounted on the tool-holder. Iron thickness: 5.3 mm. Quality: steel. Hole spacing (24 mm) compatible with most height 50 tool holders on the market (CMT, LEMAN, HOLZMANN, KITY, ISOCELE, HOLZPROFI, ELBE, etc.). A 50 mm high iron or counter-iron cannot be mounted on a 40 mm high tool holder. The iron compatible with this reference is the M215 (Ht. 50 x 5.5 mm). Diamwood PLATINUM products are top-of-the-range for intensive professional use. This product is of high quality SWISS design and complies with current standards. Diamwood, expert in equipment for the construction industry, has been mastering tools and stationary machines for over 15 years.
Data sheet
| Type of product | Contre-fers profilés |
| Colour | 5,3 |
| Height | 48 |
| new | Moulure spéciale étagère |
| Material | Acier |
| Recommendation | Bois |
| Content | 2 |
| Person responsible EU | PRESTA'DIAM 26 Chemin du Godard 38110 ST Didier de la Tour Email : contact@prestadiam.fr |
| WARNING and SAFETY | Warning and Safety Information Safety Warning: This product is intended for professional and domestic use. Please follow the instructions below to ensure safe use: Proper Use: Use this tool only in accordance with the instructions provided. Do not use this tool for unintended applications. General precautions: Always wear personal protective equipment (gloves, safety goggles, hearing protection). Make sure the work area is clean and clear. Do not use the tool near water or in damp conditions. Handling and storage: Keep the tool out of the reach of children. Store the tool in a safe, dry place when not in use. Check the condition of the tool regularly. If damaged, remove immediately from use. Risk warning: This tool may present a risk of cuts, crushing or other injuries. In the event of injury, consult a doctor immediately. Recycling and disposal: Follow local regulations for disposal of this product Person responsible in the EU for our products: PRESTA'DIAM 26 Chemin du Godard 38110 ST Didier de la Tour Email: contact@prestadiam.fr |
| User manual | Présentation du produit : Le jeu de 2 contre-fers profilés Diamwood est spécifiquement conçu pour les moulures spéciales étagères A215 pour porte-outils de toupie, garantissant une utilisation professionnelle. Utilité principale et avantages : Ces contre-fers permettent des découpes précises dans les matériaux pour le BTP tout en étant adaptés à une utilisation intensive. Leur fabrication en acier haut de gamme assure durabilité et robustesse. Caractéristiques principales : - Hauteur : 48 mm - Epaisseur : 5,3 mm - Entraxe : 24 mm - Compatible avec : La plupart des porte-outils hauteur 50 mm (CMT, LEMAN, etc.) Instructions d'utilisation : 1. Assurez-vous que le porte-outils est compatible avec les contre-fers avant l'installation. 2. Montez les fers profilés sur le porte-outils. 3. Fixez les contre-fers en respectant l'entrain pour garantir la stabilité. 4. Effectuez les réglages nécessaires afin d'obtenir les meilleurs résultats lors de la découpe. Précautions d'utilisation : - Ne pas monter ces contre-fers sur un porte-outils hauteur 40 mm. - Toujours porter des équipements de protection lors de l'utilisation pour prévenir les accidents. Entretien et nettoyage : - Nettoyez régulièrement le matériel pour maintenir son efficacité. - Rangez dans un endroit sec et sûr pour éviter toute détérioration. |
10 produits dans Profile irons
Set of 2 profiled counter-irons Ht. 38 x 4 mm BRUT A193 for router toolholders - Diamwood Platinum
Set of 2 profiled counter-irons Ht. 38 x 4 mm BRUT A193 for router toolholders - Diamwood Platinum
Set of 2 A200 rebated profiled counter-irons Ht. 48 x 5.3 mm for router tool holders - Diamwood Platinum
Set of 2 A200 rebated profiled counter-irons Ht. 48 x 5.3 mm for router tool holders - Diamwood Platinum
Set of 2 A201 profiled counter-irons height 48 x 5.3 mm tongue / groove 5 mm for router toolholders - Diamwood Platinum
Set of 2 A201 profiled counter-irons height 48 x 5.3 mm tongue / groove 5 mm for router toolholders - Diamwood Platinum
Set of 2 A202 48 x 5.3 mm tongue/groove profile cross-beams for router toolholders - Diamwood Platinum
Set of 2 A202 48 x 5.3 mm tongue/groove profile cross-beams for router toolholders - Diamwood Platinum
Set of 2 A203 48 x 5.3 mm high profiled counter-irons with 4 mm multi-groove for router tool holders - Diamwood Platinum
Set of 2 A203 48 x 5.3 mm high profiled counter-irons with 4 mm multi-groove for router tool holders - Diamwood Platinum
Set of 2 A205 48 x 5.3 mm 45° chamfer profile counter-irons for router tool holders - Diamwood Platinum
Set of 2 A205 48 x 5.3 mm 45° chamfer profile counter-irons for router tool holders - Diamwood Platinum
Set of 2 Ht. 48 x 5.3 mm A206 square and quarter-round profile counter-irons for router toolholders - Diamwood Platinum
Set of 2 Ht. 48 x 5.3 mm A206 square and quarter-round profile counter-irons for router toolholders - Diamwood Platinum
Set of 2 A209 water jet profiled counter-irons Ht. 48 x 5,3 mm for router toolholders - Diamwood Platinum
Set of 2 A209 water jet profiled counter-irons Ht. 48 x 5,3 mm for router toolholders - Diamwood Platinum
Set of 2 Louis XV A210 mouldings, height 48 x 5.3 mm, for router tool holders - Diamwood Platinum
Set of 2 Louis XV A210 mouldings, height 48 x 5.3 mm, for router tool holders - Diamwood Platinum
Set of 2 profile counter-irons Ht. 48 x 5.3 mm leave and quarter-round A214 for router tool holders - Diamwood Platinum
Set of 2 profile counter-irons Ht. 48 x 5.3 mm leave and quarter-round A214 for router tool holders - Diamwood Platinum